Archive

Posts Tagged ‘brake tester’

Agricultural tractor Brake Test would meet the road worthines

March 2nd, 2018 Comments off

Tractors To Require An O Licence

Agricultural tractors “likely” to require an O-licence

aide automotive have recently seen media reports of agricultural vehicles possibly being made to meet better road safety regulations as per commercial vehicles on UK roads.
Commercial Motor published:
Agricultural tractors that carry out commercial haulage will be subject to roadworthiness testing requirements from next year – and are likely to fall under the O-licensing regime.
From 20 May 2018, operators of agricultural tractors capable of travelling more than 40km/h (approximately 25mph), used to carry commercial goods, will be required to undergo a roadworthiness test four years after their registration and every two years thereafter.
In its response to a consultation carried out last year, the DfT also noted that operators of such tractors would likely require an O-licence.
However, the RHA said the changes did not go far enough to address the concerns about competition, and said allowing tractors to carry freight will encourage more to be used for haulage.
“Ideally we would like to see these vehicles banned from moving freight on public roads entirely as their design is not equivalent to well-designed lorries for that task,” said policy director Duncan Buchanan.
“We do not believe that the frequency, four years for the first test then every two years, is justified. It looks very odd for heavy vehicles like these to be tested so infrequently when a 50cc moped is required to be tested every year after three years.”
The FTA’s head of policy and compliance information, James Firth, added: “If it looks like a truck or it’s doing the work of a truck, test it like a truck. Members in areas where agriculture is a primary economy have long raised concerns that agricultural tractor units, and specially developed fast tractors, were competing in the haulage market without being burdened by the same safety standards.”
On the subject of O-licensing, Buchanan added: “If it is the case then operators would need to obtain O-licences from when the vehicle was new. They should also have to comply with the same level of rigour as lorries.”
Vernon Hill, director at Kings Lynn-based Vernon Hill Agricultural Services, supported bringing tractors into the O-licensing regime.
He said: “An agricultural contractor friend of mine who runs lorries and tractors thinks the cost of each is very similar, so if farmers think they are saving money by not using a haulier they may be kidding themselves.
“If they are doing commercial haulage, why shouldn’t they be in scope of O-licensing?”
The weight and speed limits for farm tractors and trailers on UK roads increased in 2015. Tractors are not currently subject to mandatory testing.
If tractors are to fall under the O licence criteria, agricultural workshops and repair engineers will have to look at regular brake testing, one way to test tractor brakes is the BrakeCheck decelerometer.
Easy to use and with hard copy print options, brake testing a agricultural tractor with a BrakeCheck would meet the road worthiness requirement of an O licence.
Contact aide automotive on 0115 8456471 for BrakeCheck pricing and any further information that me be required.
Brake Tester For Farming Tractors

Test Agri Tractor Brakes With BrakeCheck

Commercial 24 Volt Trailer Tester Van Installation

December 8th, 2017 Comments off

MT Globex Contract aide To Install TrailerCheck To Fleet Van

MT Globex is a West Midlands company that is strategically located at the heart of the UK’s motorway network, further supported by several partner depots across the UK.
MT Globex’s modern, highly maintained fleet of vehicles ensure that all their distribution operations are vastly efficient for customers with a minimal environmental footprint. Due to cutting edge, industry leading satellite tracking technology combined with fully trained transport planners with a wealth of transport knowledge, MT Globex ensure the fleet is fully utilised and thereby reducing empty mileage.
With a fleet of trailers to maintain MT Globex reviewed the TrailerCheck 4 Vanselectrical and diagnostics trailer tester as a tool to improve on trailer inspections and repairs.
Deciding to purchase the trailer tester, the next questions was: How and where shall we install the TrailerCheck in our van?
Consulting aide automotive, MT Globex decided the contract the install of the TrailerCheck to aide, utilising our experience and knowledge of best practice.
Fitting the TrailerCheck and associated accessories, MT Globex asked: Can you install the compressor as well? YES we can !
The install was completed at our workshop (on site installs also available) in one day.
If your trailer maintenance van needs a professional trailer tester with a professional install, contact aide automotive for a quote.
14 Volt Trailer Brake Tester

Commercial 24 Volt Trailer Tester Van Installation

Truck ISO ABS / EBS Susie – What Is It?

November 29th, 2017 Comments off

Faulty ISO7638 Line Can Cause Fatal Accidents

Some drivers aren’t aware of the role Of the ISO ABS / EBS Susie!

aide automotive have seen recent reports in the media of articualted truck drivers knwloedge of the ISO 7638 Susie.
We offer credit to the below article to Don Bur Ltd.
There is disturbing evidence to suggest that some drivers aren’t aware of the role and critical importance of the ABS ISO7638 line for articulated trailerswhilst in transit or, more worryingly, are deliberately leaving it disconnected.
The use of the ABS ISO7638 line (otherwise known as the EBS/ABS line) became law in May 2002 where the tractor and trailer are both provided with connections.
The EBS/ABS ‘Suzie’ connection provides electrical and data feeds to the trailer’s ECU or ‘brain’. The ECU then controls the anti-lock braking system (ABS), load sensing (LSV), roll stability (RSS) and suspension control which regulates the correct trailer ride height and, in turn, the overall trailer height.
So why then might a driver leave it disconnected? There are, surprisingly, a couple of reasons. Firstly, the roll stability system (RSS) automatically applies the brakes if the trailer is going too fast round a bend. This has an impact on both speed and fuel economy and, if a driver is either in a rush or targeted against fuel consumption, they might be tempted to disable this ‘inconvenient’ feature.
The other apathetically induced reason is that it just “doesn’t seem to do anything”. Indeed, when the driver pulls away, his/her brakes and lights will appear to work. What the driver may not understand is that they are more likely to experience jack-knifing, aquaplaning, brake lock, rollover, bridge strike and, more commonly, the fact that the 44T rig just won’t be able to stop as quickly when trying to avoid that pram that’s just peeked out from a line of parked cars.
So, just in case there is any lingering doubt, failure to connect the ABS ISO7638 line correctly results in the risk of catastrophic, life-threatening accidents. If the driver fails to use the line/ ‘Suzie’ correctly and there is a collision in which someone is killed, then the driver can face a charge of manslaughter.
aide automotive market a ISO7638 cable with fault indicator, so as well as having the cable correctly connected a driver can also be notified of any faults within the system. Again an electrical fault could have the same catastrophic effects as the ISO Susie cable being non connected.
ISOCheck lights bright RED when a fault is identified, if good to go the ISOCheck is continually lit bright GREEN.

ISO7638 Truck Tester

ISOCheck tests a trucks’ ISO sockets in order to help identify ABS or EBS faults.

80% Of Commercial Vehicle Brake Faults Cleared By Sensor Master

November 7th, 2017 Comments off

CV ABS & EBS Brake Repairs Made Easy!

The Sensor Master Clears 80% Of Commercial Vehicle Brake Faults

As the air braking world has changed, we have had to adapt the way we deal with diagnostic problems that can arise on our customers vehicle systems. As the air signalling system has been fazed out and replaced by the EBS / ABS system we have endeavored to keep up with the advancements in the technology and created our own range of testing equipment.
Our engineer is constantly updating the test equipment to match the needs that arise from his service visits, so are perfectly tuned to the EBS / ABS components that we supply.
Our test devices can be used in conjunction with the OE manufacturer’s testers to create a complete analysis structure for truck and trailers that is not only easy to use but also affordable to all sizes of fleet maintenance from owner / driver to multi fleet service garages.
Since 80% of all EBS / ABS problems are sensor related (Reported By Knorr Bremse & Wabco), by connecting to the sensor socket on each wheel, rather than the ECU, in effect, taking the quickest and most direct route, by going straight to the heart of the problem.
The Sensor Master DRA08 is a handheld EBS / ABS sensor and exciter ring tester, for use on trucks, trailers, and buses.
Lightweight and portable, the EBS /ABS CV Sensor Tester comes supplied with two 1.6m high quality cables, a sturdy carry case, short introductory printed manual, and a single 9V battery – everything, in fact, needed to use it straight out of the box.
Designed with ease of use in mind, the Commercial Vehicle ABS EBS Sensor Testertakes minutes to set-up, and, once connected, undertakes a complete test cycle of the six most common causes of EBS / ABS faults, at the touch of a button, in just 15 seconds – a fraction of the time it would take to perform the same tests manually.
Contact aide automotive to purchase this cost effective easy to use tester or buy online at our aide Online PayPal Shop.
Commercial Vehicle ABS EBS Tester

Truck ABS Faults Easily Found With Sensor Tester

aide automotive offer a range of products to help with DVSA Guide Roadworthiness

August 17th, 2017 Comments off

CV Traffic Commissioners Review & Advice

Read Some Highlights OF TC’s Annual Report for 2015-16

Recently reported in the Transport Operator, the seven traffic commissioners (TCs) of Great Britain have released their annual report for 2015-16, highlighting a broad range of transport compliance and enforcement issues identified during the course of the year, and their priorities for future progress.

The commissioners, who preside over the eight regional traffic areas, identified key concerns with regard to operator compliance, driving and maintenance standards, as well as problem areas for the authorities themselves to tackle in order to improve the services they offer.

TC Richard Turfitt, who oversees the largest traffic area, in the east of England, said he made little apology for “sounding like a broken record” when it came to vehicle inspections.

“As DVSA estimates that half of MoT fails could be avoided by checking that light-bulbs work, the condition and pressures of tyres and that mirrors, wipers and washers work, there is further work to do,” he said.

“I am appalled by the number of operators who have not even checked whether their inspection sheets are up to date by reference to DVSA’s Guide to Maintaining Roadworthiness.

“In the space of two weeks, two unconnected operators appeared before me suggesting their vehicles were being inspected against safety standards from 1972.”

aide automotive market a range of Brake Testing, Servicing & Diagnostic Tools for commercial vehicle workshops.
With the Bowmonk BrakeCheck Portable Decelerometer Printer kit, a workshop can meet the 3 additional required brake tests with minimum fuss
For Trailer Servicing & Diagnostics, aide offer a complete Trailer Electrical (ABS Light & EBS CAN Line Test), Light and Air Brake Tester with Diagnostics interface for Trailer ECU Code Reading / Clearing and management data viewing.
EBS/ABS Sensor Master testing can be conducted with the Sensor Master, while Battery Diagnostics Tests with a Midtronics MDX Battery Tester.
aide automotive offer a range of products to help with DVSA Guide Roadworthiness. Contact us via our website www.aideautomotive.com
Brake Tester, Diagnostics, Battery Testers

aide auto Market Truck & Trailer Workshop Test Tools

Motorhome Brake Testing

August 14th, 2017 Comments off

While Serving A Motorhome, Why Not Offer A Brake Test?

Check brakes and stay safe on the road this summer!!

BrakeCheck is a portable, DVSA-approved Brake Tester for all MOT class vehicles.
BrakeCheck determines braking efficiency of both the Service Brake (Foot Brake) and Hand Brake by measuring the rate of deceleration from a speed of around 20 mph (Service Brake) 10 mph (Foot Brake) until the vehicle comes to rest.
With no connection to the vehicle and designed to be self-compensating, the brake tester will indicate on the LED screen when it is positioned level enough to perform a brake test, with a generous tolerance to ensure that this is easy to achieve.
The BrakeCheck decelerometer indicates whether the vehicle pulls to the left or right during braking, and reports the overall brake efficiency of the service and hand brake. Brake test results and be compared to MOT guidelines for roadworthy vehicles.
Test results can be viewed on the display panel or downloaded to a PC for saving or printing. A printed report can also be produced at the time of testing using the portable infra-red printer.
Following the service of a Motor home or vehicle, caravan service engineers could add a hard copy brake performance test, offering confidence and professionalism to the service.
Click on Motor home Brake Testing to read more and review a sample print out.
Please do not hesitate to call to discuss further the way a decelerometer conducts a brake test – aide automotive ltd 0115 8456471
Decelerometer Bowmonk

Motor Home Brake Tester For Servicing Or MOT

aide Introduce a PayPal Online Shop For Products & Accessories

July 12th, 2017 Comments off

Commercial Vehicle Product Online Shop

aide Introduce a PayPal Online Shop For Products & Accessories

aide automotive have moved forward with a refresh on the websites category pages with the addition of a Online PayPal SuperMarket.

The Online SuperMarket can be found from the homepages navigation bar toward the top of the homepage, simple to use the shop utilises PayPal as the payment merchant. With the option to buy single or multiple items with ease, the SuperMarket will keep growing as new products are introduced or updates become available.
At present the Bowmonk BrakeCheckEBS/ABS Sensor Tester, TrailerCheck, TestaTow, Susie Easy Grips, Truck Anti Siphons, Truck Fresnel Lens, Truck 5th Wheel Lube Liner ISOCheck‘s are available now.
Further exsisitng products will be added soon, but to see all products available please click on aide automotive’s Online SuperMarket.
If you prefer to purchase with the personnel touch, please do not hesitate to call us on 0115 8456471, we accept cards as an alternative to PayPal.
Purchase A Bowmonk BrakeCheck Online

Online PayPal Purchase @ aide automotive

Bowmonk BrakeCheck User Manual Guides Available To Download

June 27th, 2017 Comments off

Bowmonk BrakeCheck User Manual  / Guide

BrakeCheck User Guides Available To Download

The Bowmonk BrakeCheck has been an impressive simple to use brake meter for many fleet operators around the world.

Even so the help of a quick user guide is always required and offer confidence the brake tester is being used correctly.
All customer can now download the main quick reference guide from our PDF download centre, To do so, go the the BrakeCheck page and towards the bottom of the page, Click on the “Download Product Data Sheet” Button.
This will then direct the user into the PDF download page where the BrakeCheck user guide can be downloaded, the BrakeCheck Print Out Explanation Guide can also be downloaded.
The Quick Reference User Guide we offer is all you should need, but if a user has any uncertainty then please call the mobile number detailed on the side of your BrakeCheck for vocal training or support.
Contact aide automotive for Bowmonk BrakeCheck Sales & Support – 0115 8456471
Decelerometer For HGV's

BrakeCheck Conducts DVSA HGV Brake Tests

Brake Testing, Servicing & Diagnostic Tools for Commercial Vehicle Workshops

May 24th, 2017 Comments off

Brake & Diagnostic Products from aide automotive

 

Truck & Bus Product Focus Feature Brake Servicing & Diagnostics had a wealth of product information recently.

aide automotive advertised a range of Brake Testing, Servicing & Diagnostic Tools for commercial vehicle workshops.
With the Bowmonk BrakeCheck Portable Decelerometer Printer kit, a workshop can meet the 3 additional required brake tests with minimum fuss
For Trailer Servicing & Diagnostics, aide offer a complete Trailer Electrical (ABS Light & EBS CAN Line Test), Light and Air Brake Tester with Diagnostics interface for Trailer ECU Code Reading / Clearing and management data viewing.
EBS/ABS Sensor Master testing can be conducted with the Sensor Master, while Battery Diagnostics Tests with a Midtronics MDX Battery Tester.
Contact aide automotive for any questions via email – info@aideautomotive.comor phone 0115 8456471
Bowmonk BrakeCheck

Brake Testing, Servicing & Diagnostic Tools for Commercial Vehicle Workshops

ISOCheck tests a trucks ISO7638 Socket

May 19th, 2017 Comments off

aide automotive launches improved ISOCheck

EBS ISOCheck Now Available In Addition To the ABS ISOCheck – Review Products Details & Buy Online

Commercial Vehicle Equipment Supplier aide automotive Has Launched An Updated Version Of The ISOCheck

ISOCheck tests a trucks’ ISO sockets in order to help identify ABS or EBS faults.

 

The latest iteration of the system – ISOCheck EBS – has been designed to test electronic braking systems incorporating a CAN line test.

“Trucks that were first used on or after 1 May 2002 must be fitted with A ISO 7638 connection,”

“If a truck is fitted with an Electronic Brake System, and is also towing a trailer that is fitted with EBS, then a 7-core cable must be used.

Like the ISOCheck ABS tester, ISOCheck EBS tests the ISO Socket 7638 pins 1 to 5, but also tests pins 6 and 7, the EBS CAN lines.

Alongside the standard ABS & EBS ISOChecks we can also offer a diagnostic EBS ISOCheck.

ISOCheck EBSPlus test pins 1 to 7, and identifies the exact pin at fault.

Once the initial power test is complete with a RED fault light, the ISOCheck will then go into diagnostic mode and flash a count sequence in relation to the faulty pin,

The ISOCheck product range has benefited from a complete redesign, incorporating the latest electronics technology which enables future proofing truck and trailer brake systems.

ISOCheck can be used to test all Wabco, Knorr-Bremse and Haldex systems, from the early generations to the latest.

Testing is simple and easy,

ISOCheck can be used in many ways: fault-finding by the roadside or as an inspection sheet test within a workshop.

ISOCheck really becomes the perfect test tool on a dark wet night. The quick test and the bright (GREEN) OK / (RED) FAULT indicator increases test and repair efficiency.

The system can also be used continuously between a unit and trailer as a constant visual aide.

To purchase the ISOCheck product range via our online PayPal shop – Click On Purchase ISOCheck Now!

More From Matthew Burke on 0115 8456471 or matt@aideautomotive.com

 

ISO7638 Truck Tester

ISOCheck tests a trucks’ ISO sockets in order to help identify ABS or EBS faults.